Belinka Zesvětlovací lazura Illumina
Code: AAABZL1K AAABZL1 Choose variantProduct detailed description
Where to use
Exterior (must be overcoated with light shades of Toplasur UV plus).
What it is applied to
Wood painted with dark stains or wood that has darkened.
What purpose it serves
Lightens dark stain coatings and covers darkened wood with a yellowish, pine-like shade.
Belinka Lightening Stain Illumina
Illumina is a stain coating for lightening wood that has darkened or has been coated with dark stains.
- Up to 25 m²/lCoverage · in one coat
- 1–2 coatsnumber of coats
- Wood structureappearance

Belinka Illumina
Illumina is a stain coating for lightening wood that has darkened or has been coated with dark stains. It lightens dark stain coatings and covers darkened wood. Illumina is a stain which, with its yellowish shade, does not change the darkened or dark background, but covers it with a shade resembling pine.
The wood grain will not be visible after the coating, but the wood structure, with proper surface preparation and correct, even application, will still be noticeable. This way, we can disguise wood defects by blackening, or fix the appearance of wood previously coated with a dark or darkened stain.
Illumina is suitable for exterior use, but it must be overcoated, preferably with light shades of Toplasur UV plus. The product does not contain biocides, i.e. no protection against blue stain, insects and wood-destroying fungi. If such protection is required, the Base impregnation must be applied before applying Illumina.
- covers (lightens) dark stain coatings
- not suitable as a standalone coating
- suitable for exterior use
Application
- Surface preparationIf the dark-coated surface is still relatively good and still has a lot of old coating on it, sand the surface with sandpaper of grit 80–100, remove the dust and apply one coat of Illumina. A surface in worse condition should first be brushed with a wire brush to remove rotten and grey wood, remnants of old coatings, dust and dirt. If you want the edges of the growth rings to be less pronounced and the surface smooth, you must sand the surface with sandpaper of grit 80–100 after brushing. After brushing, check the surface and continue treating it according to its condition. If the wood is healthy and shows no visible signs of pest infestation, use the Base product for the first coat, which will preventively protect the wood from destructive insect infestation and at the same time even out the surface. If the wood is damaged by pests, first coat the wood with the Belocid product, which will kill the pests. Usually, two coats of Illumina are needed for a surface prepared in this way, in order to achieve an even lightening.
- ApplicationIllumina is applied undiluted, with a brush or roller, in 1–2 coats on dry and properly prepared wood. Surface preparation and the number of coats depend on the degree of deterioration of the surface and the desired final appearance. On a smooth, slightly degraded and visually uniform surface, apply 1 coat. A rough, more degraded surface is more absorbent, so apply the second coat only to these areas. The aim is a visually uniform and even coating. The drying time between individual coats should be 24 hours.
- ConditionsThe ambient and surface temperature should be 20 °C. The relative humidity should be below 65%. Low temperature and high humidity can significantly affect drying.
- CleaningAfter finishing painting, remove as much paint as possible from the tools, then clean the accessories and tools with Belsol, or alternatively with white spirit or other solvents for synthetic paints.
Key information at a glance
- after 24 hrsDrying time full/next coat
- White spirit, BelsolTool cleaning
- Up to 25 m²/lCoverage · in one coat
- Brush, rollerApplication method
- Wood structureAppearance
- 1–2 coatsNumber of coats
- ExteriorArea of use
- from 5 °CPainting temperature
How much will I need?
Coverage 25 m²/l per coat. For absorbent or rough substrates, count on the upper value.
| Area | 1 coat | 2 coats |
|---|---|---|
| 10 m² | 0.4 l | 0.8 l |
| 25 m² | 1 l | 2 l |
| 50 m² | 2 l | 4 l |
When to paint
You can find the technical data sheet in the related files. To ensure correct application and to obtain all the necessary product information, we recommend that you familiarise yourself with these documents.
Need advice?
Our friendly customer support is here for you. Email us at: podpora@surtep.cz.
Free returns
Send the order back to us free of charge.
Fast dispatch
On working days we dispatch orders within 24 hours.
Additional parameters
| Category: | Tenkovrstvé |
|---|---|
| EAN: | 3838968239111 |
Discussion
Be the first who will post an article to this item!
