Eternal na Beton Komfort A+B 4,8 kg
Code: 98246645050Product detailed description
Eternal na Beton Komfort A+B 4.8 kg
Eternal na Beton Komfort A+B is a two-component, water-dilutable coating material made from epoxy resin, a water-dilutable polyamine hardener, pigments, fillers and special additives.
- 0.15–0.20 kg/m²coverage · per 1 coat
- 2–3 coatsnumber of coats
- Mattappearance

Eternal na Beton Komfort A+B
Eternal na Beton Komfort A+B is a two-component, water-dilutable coating material made from epoxy resin, a water-dilutable polyamine hardener, pigments, fillers and special additives. It is a multifunctional material for use as a primer, coating material, or self-levelling floor covering. It is intended for the interior surface treatment of concrete floors in cellars, garages, workshops, shops, warehouses, exhibition spaces and more. The coatings show very good resistance to abrasion, water, hot tyres, chemical de-icing agents, aliphatic and aromatic hydrocarbons, diluted acids, alkalis and decontamination solutions.
It has high vapour permeability, so it can also be used on fresh concrete (curing time approx. 7 days). After thorough mixing with the ETERNAL silica filler powder component, ETERNAL na beton KOMFORT can be used as a self-levelling floor covering
- Two-component coating material: Eternal na Beton Komfort A+B consists of epoxy resin and a water-dilutable polyamine hardener, which are mixed together to create a durable and versatile coating.
- Multifunctional use: It can be used as a primer, coating material, or self-levelling floor covering. It is suitable for concrete floors in cellars, garages, workshops, shops, warehouses and exhibition spaces.
- High resistance: The coatings show excellent resistance to abrasion, water, hot tyres, chemical de-icing agents, aliphatic and aromatic hydrocarbons, diluted acids and alkalis.
- Vapour permeability: Thanks to its high vapour permeability, Eternal na Beton Komfort can also be used on fresh concrete after a minimum curing time of 7 days.
- Use with the powder component: After mixing with Eternal silica filler, the coating can be used as a self-levelling floor covering.
Application
- Substrate preparationBefore application, the substrate must be firm, dry and clean, free from dirt and grease.
- Mixing the components– Component A (epoxy resin) is mixed with component B (hardener) in a ratio of 5:1. The mixture is stirred for 5 minutes, then left to stand for 5 minutes, and briefly stirred again before application.
- Application– The coating is applied with a brush, roller or by spraying (air, airless, airmix). Only the already hardened mixture may be diluted; the individual components cannot be diluted before mixing.
- Primer coat– First, a primer coat of diluted paint is applied. After 6 hours of drying, 2–3 coats of undiluted paint are applied with a 24-hour interval between coats at a temperature of 20–25 °C. Lower temperatures extend the drying time.
- Self-levelling floor covering– After mixing the hardened material with ETERNAL silica filler in a 1:1 ratio, the coating can be used as a self-levelling floor covering. When preparing the mixture, care must be taken not to mix air into the material.
- ConditionsThe temperature of the substrate and surroundings during application should be between 10–30 °C.
- CleaningAfter finishing painting, immediately remove as much of the coating material from the tools as possible, then wash them with clean water.
Key information at a glance
- 24 hrsDry to the touch
- With waterTool cleaning
- 0.15–0.20 kg/m²Coverage · per 1 coat
- Spraying/roller/ brushApplication method
- MattAppearance
- 2–3 coatsNumber of coats
How much will I need?
Coverage 5–6.7 m²/kg per coat. For absorbent or rough substrates, expect the higher value.
| Area | 2 coats | 3 coats |
|---|---|---|
| 10 m² | 3–4 kg | 4.5–6 kg |
| 25 m² | 7.5–10 kg | 11.3–15 kg |
| 50 m² | 15–20 kg | 22.5–30 kg |
You can find the technical data sheet, safety data sheet and colour chart in the related files. To ensure proper application and to obtain all the necessary information about the product, we recommend that you familiarise yourself with these documents. More information on safety during transport, storage, handling, as well as disposal and ecology, can be found in the safety data sheet.
Need some advice?
Our friendly customer support team is here for you. Email us at: podpora@surtep.cz.
Free returns
Send your order back to us free of charge.
Fast dispatch
We dispatch orders within 24 hours on business days.
Additional parameters
| Category: | Krycí barvy |
|---|---|
| EAN: | 8590892119758 |
Discussion
Be the first who will post an article to this item!
Výrobce:
| Manufacturing company : | AUSTIS a. s |
|---|---|
| Address : | K Austisu 680, 154 00 PRAHA 5 - Slivenec Česká republika |
| E-mail : | austis@austis.cz |
